Appendix 5: Analysis of solutions observed in the field - Use of a single ascender with knots in the rope.
- Read the technical notice before viewing the following techniques.
- It is important to fully understand the information provided in the technical notice before using this complementary information
- Mastering these techniques requires training.
- Consult a professional before attempting to perform these techniques on your own.
Primary system: one ascender on the rope.
Secondary system: knots tied in the rope while climbing, below the ascender.
The knots are left in the rope below the climber.
- Simplicity of the system and its installation
- Low equipment cost
- The redundancy principle is not followed with respect to the belay rope WARNING, repeated rubbing against the rock can quickly cut your only rope.
- Need to regularly have both hands free to make knots: impossible if the climb is overhung, so there is a risk of climbing rather far above the last knot in certain sections
- In case topping out is necessary to exit the route, retrieving a rope with many knots in it could be complicated or even dangerous
Risks in case of primary ascender malfunction:
- Significant potential fall length
- The user will fall to the first knot in the rope The ascender is not designed to sustain the impact on the knot.
Results of a series of tests carried out by Petzl:
Test scenario: simulation of primary device malfunction. Cam intentionally deactivated for the test Fall onto the knot with an 80 kg dummy attached to the ascender.
The start of the fall is fixed 2 m from the anchor, at an average position: closer to the anchor, the fall factor will be higher and the impact more severe.
Two fall heights were envisioned:
- Standard fall height = 2 m fall above the knot (factor 0.5)
- Fall height of a climber required to climb through a sustained section = 5 m fall above the knot (factor 0.71)
The same falls were repeated on 11 mm diameter dynamic, low stretch kernmantel, and static ropes.
During these tests, the knot stopped the fall each time. However, stopping the fall is not a sufficient result to validate these tests, because the climber is then faced with other problems.
- The impact force is high: always greater than 4 kN, and up to more than 8 kN for falls on static and low stretch kernmantel ropes
- The rope is sometimes damaged (sheath torn, several core strands broken): when the cam re-engages during the fall, or when impacting the knot
- The device is damaged by the impact in most cases:
> MINI TRAXION: bent side plates and axle. The device is no longer usable; the climber must use another ascender, or descender, to escape.
> MICRO TRAXION: bent moving side plate and axle. The device might be usable for escape, but must be retired immediately afterward.
> ASCENSION: bent frame in the most severe cases. The device might be usable for escape, but must be retired immediately afterward. The knot jams between the carabiner and the body of the device. In case of a poor attachment, the rope will come free.
Petzl dœs not recommend this solution as its effectiveness is uncertain.
- Good practices for belaying a lead climber
- Universal technique for correct use of a belay device.
- Spotting and belaying at the start of the route
- Belaying a leader climber: vigilance, anticipation and mobility
- Stopping a climbing fall
- Communication when climbing
- Top-rope belaying with the GRIGRI anchored to the ground.
- Belaying with the GRIGRI
- Video: Belaying with a GRIGRI
- VIDEO - Specific left-handed technique
- Belaying with the REVERSO
- Video - The Worst Belayer in the World
- Carabiner basics
- Choice of carabiner for attaching a GRIGRI to the harness
- Choice of carabiners for attaching a VERSO or REVERSO to the harness
- Choice of lanyard end carabiner for a rock climbing or via ferrata lanyard
- Choice of carabiners for attaching the rope to the anchor
- Examples of dangerous carabiner loading.
- Attaching a rope to the harness
- To read for self-belaying
- General principles for solo climbing with a fixed belay rope
- Setting up a self-belay system on two ropes with two ascenders
- Installation on one single rope with two ascenders
- Appendix 1: Petzl dœs not recommend using only one ascender for self-belaying.
- Appendix 2: Detail of installation on two ropes with two ascenders
- Appendix 3: Detail of installation on one rope with two ascenders
- Appendix 4: Precautions and introduction to risk analysis
- Appendix 5: Analysis of solutions observed in the field - Use of a single ascender with knots in the rope.
- Appendix 6: Analysis of solutions observed in the field. Use of one ascender and clipping into knots on a second rope